www.millerpaint.com
1-800-852-3254
Evolution Lifetime Exterior
Flat 8500 series
VOC Compliant
Bases Available: 8500 - White, 8582 - Medium, 8586 - Accent, 8588 - Neutral
Product Description     Specifications

Our finest 100% pure acrylic resin is formulated with the most advanced technology to create Evolution. Evolution has our highest solids content to provide lasting durability. Highly washable, superior color retention, excellent adhesion and improved resistance to mold, mildew and algae. Covered by our Lifetime Warranty (see label).

    
Color: Full range

Finish: Flat

Density: 12.5# per gallon

Clean-Up: Mild soap and water

VOC: 70 gm/liter

Solids: Weight
Volume		 62.0%
47.4%

Flash Point: N/A

Coverage: One or two coats @250-400 square feet per gallon. 3-4 dry mil ideal film thickness per coat.

Theoretical
Coverage:		 253 sq. ft. @ 3 dry mils

Dry Time: 30 minutes to touch and two hours to recoat @ 70°F and 50% relative humidity.

Application: Brush, roll or spray.  Do not apply when surface or air temperatures are below 35°F or when temperatures are expected to drop below 35°F within 24 hours.
Features

Pure 100% acrylic co-polymer modified resin improved for prolonged adhesion. Evolution has excellent adhesion, color retention and has high film build to cover extremely well. Formulated for better long term flexibility. Evolution applies easily and is manufactured for minimal roller splatter. Ideal for lasting durability on many properly prepared exterior substrates. Evolution can be applied at a rate of 250 sq. ft. per gallon to yield a 3 mil dry film thickness in one application.
Composition

100% pure acrylic resin
Titanium dioxide & extender pigments
Contains no lead or mercury
VOC compliant










Surface Preparation
Surfaces must be sound, dry and clean. Remove previous coatings that have poor adhesion. Wash areas where mold and mildew are present. Remove all dirt, oil, grease, wax and/or other contaminant. Repair cracks and fill voids. De-gloss shiny surfaces by lightly sanding. Clean and prime all metal surfaces with an appropriate primer. Prime areas as needed. Test for adhesion and compatibility with existing finishes.
Disposal
Never pour leftover coating down any sink or drain—use up material on the job or seal can and store safely for future use. Do not incinerate closed containers. For specific disposal or recycle guidelines, contact your local waste management agency or district. Always attempt to recycle whenever possible.
Limited Lifetime Warranty

If this Evolution™ exterior coating by Miller Paint Co., Inc., when applied in accordance with label instructions, fails to perform due to peeling, blistering or unusual wear for as long as you own the single-family home to which this paint was applied, then we will either replace the paint free of charge or refund the purchase price, upon presentation of proof of purchase. This warranty, which excludes failure due to deterioration of the underlying surface, structural defects or failure of previous paint, extends only to the owner of the single-family home to which the paint was applied during such owner’s occupancy, may not be transferred or assigned, and is your sole remedy.  THIS WARRANTY DOES NOT INCLUDE LABOR OR THE COST OF LABOR FOR THE APPLICATION OF ANY PRODUCT, AND EXCLUDES ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.  Some states do not allow the exclusion of incidental or consequential damages, so the limitation may not apply to you.  This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Possible Existing Lead Warning
WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Product Analysis figures should be taken as accurate for products being produced at the time of publication. Formulation improvements may be made from time to time that may affect these figures to some degree. Also, manufacturing tolerances of ±2% are considered acceptable. Whenever a change is made that the Manufacturer considers substantial, the Product Analysis will be revised.