For pricing and availability, please contact one of over 50 Miller Paint stores throughout Oregon, Washington and Idaho. Also available at many authorized dealers.
Ideal for projects where a deep, rich look is desired yet only a minimal sheen is needed. This finish has a minimal sheen that is mostly seen at an angle. It reduces dirt pick-up and provides some washability. Ideal for full body exterior work where some sheen is desired. Best used when the surface is free of major imperfections.
Approximately 250 to 500 square feet per gallon. Two coats recommended. Coverage depends on porosity and proﬁle of surface and can be less when making a signiﬁcant change in color.
30 minutes to touch, 2 hours to recoat, at 70°F and 50% relative humidity
Never pour leftover material down any sink or drain. Use up material on the job, or seal can and store safely for future use. Do not incinerate closed containers. For specific disposal guidelines contact your local waste management agency or visit millerpaint.com/paint-recycling. Please re-use or recycle.
REPAIR cracks and fill voids with a paintable patching/caulking material. Degloss all shiny, smooth, hard, or glossy surfaces by lightly sanding. Remove all loose and scaling paint.
CLEAN all paintable surfaces to be free of dirt, dust, oil, grease, wax, and other contaminants. Rinse and allow surface to dry completely.
PRIME unsealed surfaces such as ferrous metal, plaster/wallboard, cedar, redwood, and other wood surfaces that may contain tannins or water stains with an appropriate Miller Paint primer. Test for adhesion and compatibility when painting over existing finishes.
STIR thoroughly before use. Thinning not recommended. If necessary, use a small amount of clean tap water. Do not use solvent to thin.
APPLY using nylon or synthetic brush, pad, roller, or spray. Do not apply when surface temperatures are below 35°F or when temperatures are expected to drop below 35°F within 24 hours. Keep product from freezing.
CLEANUP by removing all paint spatters, and wash all brushes and equipment immediately with warm soapy water. Follow with a clear rinse.
LIMITED LIFETIME WARRANTY: If this Miller Paint Evolution Exterior Paint, when applied in accordance with label instructions and technical data sheet, blisters or peels for as long as you own the single-family home to which this paint was applied, then Miller Paint Co., Inc. will either provide an equivalent paint product in an amount sufficient for repair free of charge, or refund the original purchase price, but only upon presentation of original proof of purchase. This warranty, which excludes failure due to deterioration of the underlying surface, structural defects or failure of previous paint, inadequate surface preparation or application of the product, extends only to the owner of the single-family home to which the paint was applied during such owner’s occupancy, may not be transferred or assigned, and is your sole and exclusive remedy. THIS WARRANTY DOES NOT INCLUDE LABOR OR THE COST OF LABOR FOR THE APPLICATION OF ANY PRODUCT, AND EXCLUDES ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion of incidental or consequential damages, so the limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.
Blistering and peeling of exterior house paints down to the bare wood is usually caused by moisture behind the paint film. Moisture pressure forces the paint away from the surface. Sources of excess moisture in the wood must be eliminated prior to repainting. Old, unsound multiple coat paint systems may be subject to peeling when repainted due to the added weight and stress created by paint layers. In such cases, all old paint layers must be removed back to bare wood before repainting.
The contents of this can should be well stirred or boxed by pouring from one can to another to assure color uniformity. More than one can of the same color should be mixed together as you progress with your work. Check color before painting, not responsible for application of wrong shade. Custom colors are not returnable.
Specifications Evolution Exterior Wall Finish
|VISCOSITY||100-105 KU||100-105 KU|
|Weight Per Gallon||11.26 (LB)||11 (LB)|
|Gloss||2-6% @60° | 5-20% @85°||10-20% @60° | 30-45% @85°|
|VOC* (minus water)||49 g/L||49 g/L|